MR-J4-500A Bộ điều khiển Servo Driver Mitsubishi 5 kW 3 Pha 220 VAC

Mã Sản Phẩm: : MR-J4-500A
Tên Sản Phẩm: : MR-J4-500A Bộ điều khiển Servo Driver Mitsubishi 5 kW 3 Pha 220 VAC
Danh Mục: : Servo Driver
Thương Hiệu: : Servo Driver MR-J4
Giá: : Liên Hệ

Chi Tiết Sản Phẩm

MR-J4-500A Bộ điều khiển Servo Driver Mitsubishi 5 kW 3 Pha 220 VAC

Bộ điều khiển động cơ Servo Mitsubishi dòng MR-J4-A
Điện áp hoạt động:
- 3 pha 220VAC
Công suất: 5KW
Phần mềm cấu hình: Mr Configurator 2-SW1DNC-MRC2-E
- Cáp Encoder kết nối Bộ điều khiển MR-J4 với động cơ Servo Motor: Cáp Encoder MR-J4
- Cáp Nguồn kết nối Bộ điều khiển MR-J4 với động cơ Servo Motor: Cáp nguồn MR-J4
- Cáp phanh kết nối Bộ điều khiển MR-J4 với động cơ Servo Motor: Cáp phanh MR-J4

Thông số kỹ thuật Bộ điều khiển động cơ Servo-MR-J4-A Servo Driver Amplifier:

Servo amplifier model MR-J4-		100A	200A	350A	500A	700A
Output	Rated voltage	3-phase 170 V AC
	Rated current [A]	6	11	17	28	37
Main circuit power supply	Voltage/frequency (Note 1)	3-phase 200 V AC to 240 V AC, 50/60 Hz
	Rated current [A]	5	10.5	16	21.7	28.9
	Permissible voltage fluctuation	3-phase 170 V AC to 264 V AC
	Permissible frequency fluctuation	±5% maximum
Control circuit power supply	Voltage/frequency	1-phase 200 V AC to 240 V AC, 50/60 Hz
	Rated current [A]	0.2			0.3
	Permissible voltage fluctuation	1-phase 170 V AC to 264 V AC
	Permissible frequency fluctuation	±5% maximum
	Power consumption [W]	30			45
Interface power supply		24 V DC ± 10% (required current capacity: 0.5 A (including CN8 connector signal))
Load-side encoder interface (Note 9)		Mitsubishi high-speed serial communication
Tolerable regenerative power of the built-in regenerative resistor (Note 2, 3) [W]		20	100	100	130	170
Control method		Sine-wave PWM control/current control method
Dynamic brake		Built-in (Note 4)
Protective functions		Overcurrent shut-off, regenerative overvoltage shut-off, overload shut-off (electronic thermal), servo motor overheat protection, encoder error protection, regenerative error protection, undervoltage protection, instantaneous power failure protection, overspeed protection, error excessive protection
Position control mode	Maximum input pulse frequency	4 Mpps (when using differential receiver), 200 kpps (when using open-collector)
	Positioning feedback pulse	Encoder resolution: 22 bits
	Command pulse multiplying factor	Electronic gear A/B multiple, A: 1 to 16777216, B: 1 to 16777216, 1/10 < A/B < 4000
	Positioning complete width setting	0 pulse to ±65535 pulses (command pulse unit)
	Error excessive	±3 rotations
	Torque limit	Set by parameters or external analog input (0 V DC to +10 V DC/maximum torque)
Speed control mode	Speed control range	Analog speed command 1:2000, internal speed command 1:5000
	Analog speed command input	0 V DC to ±10 V DC/rated speed (Speed at 10 V is changeable with [Pr. PC12].)
	Speed fluctuation rate	±0.01% maximum (load fluctuation 0% to 100%), 0% (power fluctuation: ±10%) ±0.2% maximum (ambient temperature: 25 °C ± 10 °C) only when using analog speed command
	Torque limit	Set by parameters or external analog input (0 V DC to +10 V DC/maximum torque)
Torque control mode	Analog torque command input	0 V DC to ±8 V DC/maximum torque (input impedance: 10 kΩ to 12 kΩ)
	Speed limit	Set by parameters or external analog input (0 V DC to ± 10 V DC/rated speed)
Fully closed loop control		Available in the future
Safety function (Note 10)		STO (IEC/EN 61800-5-2)
Safety performance	Standards certified by CB	EN ISO 13849-1 Category 3 PL d, EN 61508 SIL 2, EN 62061 SIL CL 2, EN 61800-5-2 SIL 2
	Response performance	8 ms or less (STO input OFF → energy shut-off)
	Test pulse input (STO) (Note 7)	Test pulse frequency: 1 Hz to 25 Hz, Test pulse off time: 1 ms maximum
	Mean time to dangerous failure (MTTFd)	100 years
	Average diagnostic coverage (DCavg)	90%
	Probability of dangerous Failure per Hour (PFH)	1.01 × 10-7 [1/h]
Compliance to standards	CE marking	LVD: EN 61800-5-1, EMC: EN 61800-3, MD: EN ISO 13849-1, EN 61800-5-2, EN 62061
	UL standard	UL 508C
Communication function		USB: Connect a personal computer (MR Configurator2 compatible)
		RS-422: 1 : n communication (up to 32 axes) (Available in the future)
Structure (IP rating)		Force cooling, open (IP20)			Force cooling, open (IP20) (Note 5)
Close mounting		Possible (Note 6)			Not possible
Mass [kg]		1.4	2.1	2.3	4	6.2

Kết hợp động cơ Servo Motor: Bộ điều khiển 1 trục với động cơ Servo

Servo amplifier	Rotary servo motor	Linear servo motor (primary side) (Note 1)	Direct drive motor
MR-J4-10A	HG-KR053, 13 HG-MR053, 13	Available in the future
MR-J4-20A	HG-KR23 HG-MR23		Available in the future
MR-J4-40A	HG-KR43 HG-MR43
MR-J4-60A	HG-SR51, 52
MR-J4-70A	HG-KR73 HG-MR73
MR-J4-100A	HG-SR81, 102
MR-J4-200A	HG-SR121, 201, 152, 202
MR-J4-350A	HG-SR301, 352
MR-J4-500A	HG-SR421, 502
MR-J4-700A	HG-SR702